Results 1 to 3 of 3

Thread: Spare Mag & Knife Back Pocket Carrier

  1. #1
    Member  
    Join Date
    09-07-07
    Posts
    52

    Spare Mag & Knife Back Pocket Carrier

    I'm probably like a lot of you and take advantage of whatever pockets I've got on my pants. A number of years ago I stopped carrying my wallet in my back pocket. My problem was the same one that George Costanza had in Seinfield. My wallet always got about two inches thick which is not conducive to sitting on so to avoid the sore butt I switched to front pocket carry or cargo pocket carry if my pants had one. From then on I've been happily sitting on empty back pockets...until now.

    Since it's the summer I've been shying away from my typical two gun carry (Sig P239 IWB & Kahr PM9 in the pocket) and just wearing one (typically the PM9) along with a spare mag. A while back I had made a horizonal mag carrier that was tuckable and while it works it's not the easiest to put on so I've found myself dropping the spare in a pocket. We all know that's not the best way to do it. If I dropped it in my back pocket it would fall any which way and wasn't comfortable to sit on. In any other pocket I never knew which way it would be when I yanked it out. So I need a solution.

    For my birthday this year I got treated to a new EDC knife - a SOG FlashII (thank you nutnfancy for his review on the blade). While it has a wonderfully low carry pocket clip I prefer to keep it as out of the way as possible. I've had the unfortunate car scratch from a similar clip. So my solution for my mag can also be a solution for my knife.

    Here it is.


    You'll notice I used a single rivet on the mag side. The reason for this is that there is no retention on the mag except for the little bit of friction of the kydex so I wanted to keep that tight. The knife has all kinds of little protrusions so it needs a bit of looseness so that it'll draw cleanly. I kept the clip on the knife so that I have the option to use it if I ever need to. You can see I angled them slightly away from each other so that there won't be any interference. You may also notice that it's been a while since I've molded kydex and I scorched a little bit on the mag side. That heat gun gets HOT!


    The whole thing measures 4 1/4 inches wide, under 5 inches high and less than 3/4 inch in thickness. I wear it in my weak side back pocket with the flat side out so it just looks like a wallet. The knife and mag stay where they are until I reach in and pull them. I can even "reholster" them without having to take the carrier out of my pocket. Sitting down I can tell it's there, but since it's pretty thin as long as I'm on some kind of cushion I'm comfortable.

    All in all a success. This is the kind of thing that is too custom for most commercial kydex makers to put out since the combination of mag and knife can vary drastically. If you want to have something like this my advice is to make it yourself. It's not hard to do and you'll end up with something no one else has.
    Mine: S&W 908.....Wife's: Ruger SP101 3"
    ------Kahr PM9...............Sig P239 (it's her's now)
    ------Norinco 213...........Charter Arms Undercover
    Blog: http://hiddendefense.blogspot.com/

  2. #2
    Member  
    Join Date
    10-20-08
    Posts
    45
    Interesting. Do you have a source for the kydex, you can cite. Are you using the miss's hair dryer or one of the soldering type heaters?

  3. #3
    Member  
    Join Date
    09-07-07
    Posts
    52
    The kydex I ordered from knifekits.com. For this application I used a heat gun to mold it. I normally would have used a toaster oven to get the initial shape and then used the heat gun to loosen it up, but our toaster oven was in storage and not easy to get to.
    Mine: S&W 908.....Wife's: Ruger SP101 3"
    ------Kahr PM9...............Sig P239 (it's her's now)
    ------Norinco 213...........Charter Arms Undercover
    Blog: http://hiddendefense.blogspot.com/

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •